Serial Port eTOP300 (PLC)

Sériové porty a kabely pro řady eTOP300, eTOP500 (případně eTOP400)
ÚVOD
LINKY NA WEBY VÝROBCE:
http://www.uniop.com/webpage?ReadForm=1&wPageName=search&sc=&t=&sl=53
http://www.jmobile.net/webpage?ReadForm=1&wPageName=search&sc=&t=&q=&sl=52
http://www.exor.de/index.php/su-men-down/viewcategory/28-k
Pokud není k dispozici schéma pro určité PLC a novou řadu eTOP300/500 s 9 pin portem, lze použít schema
pro klasické UniOPy s 15 pin portem, viz např.
http://www.uniop.com/webpage?ReadForm=1&wPageName=search&sc=&t=&q=&sl=53
Klasické kabely jsou bez označení D9 (tj. CAxxx; nikoliv CAxxx – D9, které jsou pro 9 pin port) a ke
klasickým kabelům lze použít dle typu komunikace adaptéry CA227, 228 a CA250, nebo samozřejmě dle
daného osazení pinů předělat starý kabel s 15 pin Canon na 9 pin Canon.
Adaptéry CA227, 228 a CA250 jsou pro přehled na konci tohoto manuálku.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Serial Port eTOP300 (PLC)
Výňatek z kap. 5.1:
MANUGENETOP3xx UniOP
Operating Instructions
VER 1.03
manugenetop3xx.pdf
The serial port is used to communicate with the PLC or with another type of controller.
Different electrical standards are available for the signals in the PLC port connector: RS-232, RS-422, RS-485.
The serial port is software programmable. Make sure you select the appropriate interface in
the programming software.
RS-422, RS-485
Pin
1
2
3
4
5
6
7
8
9
RS-232
Description
GND
Pin
1
2
3
4
5
6
7
8
9
CHACHB+5V output
CHB+
CHA+
Description
GND
TX
RX
+5V output
CTS
RTS
SERIAL PORT
The communication cable must be chosen for the type of device being connected.
Serial PLC Port, str. 40-41 - older UniOPs, 15 pins
(not for eTOP300, eTOP400, TOP500)
Výňatek z:
UniOPTM
Universal Operator Panel
Installation Guide
Document code MANUUNIOP22
Version 1.09
Date 03.02.2012
u22_1-09.pdf
The PLC Port is used to communicate with the PLC or with another type of controller; if the panel is configured as an
UniNET client, then this port may be used for the network connection.
Different electrical standards are available for the signals in the PLC port connector: RS-232, RS-422, RS-485 or Current
Loop 20 mA. The cable used selects the appropriate signals. It is always necessary to use the correct cable type for on the
PLC to be connected.
Note: If the proper cable is not used, communication with the PLC will not be possible.
The connector is a D-15 pin male. Pin assignment is shown in the table below.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Description
Frame Ground
RXD
TXD
+5 V output (Max 100mA)
GND
CHACHBTX+ 20 mA
TX- 20 mA
RTS
CTS
RX+ 20 mA
RX- 20 mA
CHA+
CHB+
Figure 37 - PLC Port connector and pin assignment
The communication cable must be chosen for the type of device being connected.
CA227
Date: December 9, 2009
Ref: CA227-1
Revision: 02
Author: TS
Cable code
Description
Type of Communication
Panel Connector
Device Connector
Notes
CA227
UniOP adapter for PLC/PC port for eTOP300 series and for
TCA11 board
RS-422 – RS485 4 wire
D-sub type 9P – male
D-sub type 15P - male
Table 1. Cable description
Panel
to 15 pin cables
CONNECTOR HOOD
shield
4
3
1
8
7
6
CHB-
CHB-
CHA-
CHA-
GND
GND
CHA+
CHA+
CHB+
CHB+
+5VEXT
+5VEXT
Figure 1. Cable diagram
CA227-3 - December 15, 2009
Copyright  2009 Sitek s.p.a. All rights reserved.
1
7
6
5
14
15
4
CA228
Date: December 9, 2009
Ref: CA228-1
Revision: 01
Author: TS
Cable code
Description
Type of Communication
Panel Connector
Device Connector
Notes
CA228
UniOP adapter for PLC/PC port for eTOP300 series and for
TCA11 board
RS-232
D-sub type 9P – male
D-sub type 15P – male
table 1. Cable description
Panel
to 15 pin cables
CONNECTOR HOOD
shield
4
3
1
8
7
6
RX
RX
TX
TX
SHIELD
GND
RTS
RTS
CTS
CTS
+5VEX+
+5VEX+
figure 1. Cable diagram
CA228-1 - December 9, 2009 - Preliminary
Copyright  2009 Exor Electronics R&D. All rights reserved.
1
2
3
5
10
11
4
CA250
Date: December 9, 2009
Ref: CA250-1
Revision: 00
Author: TS
Cable code
Description
Type of Communication
Panel Connector
Device Connector
Notes
CA250
UniOP adapter PLC/PC port for eTOP300 series and TCA11
board
RS-485
D-sub type 9P – male
D-sub type 15P - male
Table 1. Cable description
Panel
to 15 pin cables
CONNECTOR HOOD
shield
4
3
1
8
7
6
CHB-
1
7
CHA-
CHA-
SHIELD
GND
CHA+
CHA+
CHB+
6
5
14
15
+5VEXT
+5VEXT
Figure 1. Cable diagram
CA250-1 - December 9, 2009
Copyright  2009 Sitek s.p.a. All rights reserved.
4