VHM-Mikro-Pilotbohrer zum Anbohren und - PM
Transkript
VHM-Mikro-Pilotbohrer zum Anbohren und - PM
612 VHM-Mikro-Pilotbohrer zum Anbohren und Zentrieren Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: degressiv Spitzenwinkel: 140° Anschnitt: 4 Flächen HM-Sorte: EZ61 Ausspitzung: selbstzentrierend Beschichung: TiAlN Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von hochfesten Materialien. Exakte Zentrierbohrung mit 90°-Fase für optimale Führung und Positionsgenauigkeit der anschließenden Tieflochbohrung. PremiumHartmetall und polierte Schneiden ermöglichen lange Standzeiten und prozesssicheres Bohren in der Großserie. Solid carbide micro pilot drill for spot drilling and centering Design: 2 flutes Cutting: RH Helix angle: degressive Point angle: 140° Chamfer: 4 facet pointing Carbide grade: EZ61 Point: self-centering Coating: TiAlN Geometry and carbide designed for microprocessing of high-strength materials. Precise centering hole with a 90° bevel for perfect guidance and positioning accuracy of the subsequent deep hole bore. Premium carbides and polished cutting edges enable long service lives and reliable drilling for large quantities in volume production. Micro-foret piloté en carbure monobloc pour le perçage et le centrage Modèle : 2 dents Sens de coupe : droite Angle d'hélice : dégressive Angle de pointe : 140° Affûtage : 4 facettes Sorte de carbure : EZ61 Affûtage en pointe : autocentrant Revêtement : TiAlN Géométrie et sorte de carbure spécialement conçus pour le micro-usinage de matériaux à résistance élevée. Perçage central précis avec chanfrein à 90° pour un guidage optimal et une précision de positionnement du perçage pour trous profonds. Le carbure haute qualité et les tranchants polis permettent d‘atteindre des durées d‘usage élevées et de réaliser un perçage fiable pour les grandes séries. 38 Bestell-Nr. order no N° référence 612.050 612.055 612.060 612.065 612.070 612.075 612.080 612.085 612.090 612.095 612.100 612.105 612.110 612.115 612.120 612.125 612.130 612.135 612.140 612.145 612.150 612.155 612.160 612.165 612.170 612.175 612.180 612.185 612.190 612.195 612.200 612.205 612.210 612.215 612.220 612.225 612.230 612.235 612.240 612.245 612.250 612.255 612.260 612.265 612.270 612.275 612.280 612.285 612.290 612.295 612.300 612.310 612.320 612.330 612.340 612.350 612.360 612.370 612.380 612.390 612.400 d1 l1 d2 l2 l d 0,50 0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1,00 1,05 1,10 1,15 1,20 1,25 1,30 1,35 1,40 1,45 1,50 1,55 1,60 1,65 1,70 1,75 1,80 1,85 1,90 1,95 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 3,00 3,10 3,20 3,30 3,40 3,50 3,60 3,70 3,80 3,90 4,00 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 1,9 2,0 2,1 2,2 2,3 2,4 2,5 2,6 2,7 2,8 2,9 3,0 3,1 3,2 3,3 3,4 3,5 3,6 3,7 3,8 3,9 4,0 4,1 4,2 4,3 4,4 4,5 4,6 4,7 4,8 4,9 5,0 5,1 5,2 5,3 5,4 5,5 5,6 5,7 5,8 5,9 6,0 6,2 6,4 6,6 6,8 7,0 7,2 7,4 7,6 7,8 8,0 1,2 1,3 1,4 1,5 1,8 1,8 2,0 2,0 2,0 2,0 2,2 2,2 2,2 2,2 2,2 2,5 2,5 2,5 2,5 2,7 2,7 2,7 2,7 2,8 2,8 2,8 2,8 3,0 3,0 3,0 3,0 3,2 3,2 3,2 3,2 3,4 3,4 3,4 3,4 3,6 3,6 3,6 3,6 3,8 3,8 3,8 3,8 4,0 4,0 4,0 4,0 4,5 4,5 4,8 4,8 4,8 5,0 5,0 5,4 5,4 5,4 3,5 3,8 4,1 4,5 5,2 5,3 5,8 5,9 6,0 6,1 6,6 6,7 6,8 6,9 7,0 7,8 7,9 8,0 8,1 8,6 8,7 8,8 8,9 9,2 9,3 9,4 9,5 10,0 10,1 10,2 10,3 10,8 10,9 11,0 11,1 11,6 11,7 11,8 11,9 12,5 12,6 12,7 12,8 13,3 13,4 13,5 13,6 13,9 14,0 14,1 14,2 15,4 15,6 16,4 16,6 16,8 17,5 17,7 18,7 18,9 19,1 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 55 55 55 55 55 55 55 55 55 55 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 613 VHM-Mikro-Pilotbohrer zum Anbohren und Zentrieren Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: degressiv Spitzenwinkel: 140° Anschnitt: 4 Flächen HM-Sorte: EZ61 Ausspitzung: selbstzentrierend Beschichung: TiAlN Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von hochfesten Materialien. Exakte Zentrierbohrung mit 90°-Fase für optimale Führung und Positionsgenauigkeit der anschließenden Tieflochbohrung. PremiumHartmetall und polierte Schneiden ermöglichen lange Standzeiten und prozesssicheres Bohren in der Großserie. Solid carbide micro pilot drill for spot drilling and centering Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: degressive Point angle: 140° Chamfer: 4 facet pointing Carbide grade: EZ61 Point: self-centering Coating: TiAlN 613.050 613.055 613.060 613.065 613.070 613.075 613.080 613.085 613.090 613.095 613.100 613.105 613.110 613.115 613.120 613.125 613.130 613.135 613.140 613.145 613.150 613.155 613.160 613.165 613.170 613.175 613.180 613.185 613.190 613.195 613.200 Geometry and carbide designed for microprocessing of high-strength materials. Precise centering hole with a 90° bevel for perfect guidance and positioning accuracy of the subsequent deep hole bore. Premium carbides and polished cutting edges enable long service lives and reliable drilling for large quantities in volume production. Micro-foret piloté en carbure monobloc pour le perçage et le centrage d1 l1 d2 l2 l d 0,50 0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1,00 1,05 1,10 1,15 1,20 1,25 1,30 1,35 1,40 1,45 1,50 1,55 1,60 1,65 1,70 1,75 1,80 1,85 1,90 1,95 2,00 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 1,9 2,0 2,1 2,2 2,3 2,4 2,5 2,6 2,7 2,8 2,9 3,0 3,1 3,2 3,3 3,4 3,5 3,6 3,7 3,8 3,9 4,0 1,2 1,3 1,4 1,5 1,8 1,8 2,0 2,0 2,0 2,0 2,2 2,2 2,2 2,2 2,2 2,5 2,5 2,5 2,5 2,7 2,7 2,7 2,7 2,8 2,8 2,8 2,8 3,0 3,0 3,0 3,0 1,80 1,95 2,10 2,25 2,70 2,70 3,00 3,00 3,00 3,00 3,30 3,30 3,30 3,30 3,30 3,75 3,75 3,75 3,75 4,05 4,05 4,05 4,05 4,20 4,20 4,20 4,20 4,50 4,50 4,50 4,50 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Modèle : 2 dents Sens de coupe : droite Angle d'hélice : dégressive Angle de pointe : 140° Affûtage : 4 facettes Sorte de carbure : EZ61 Affûtage en pointe : autocentrant Revêtement : TiAlN Géométrie et sorte de carbure spécialement conçus pour le micro-usinage de matériaux à résistance élevée. Perçage central précis avec chanfrein à 90° pour un guidage optimal et une précision de positionnement du perçage pour trous profonds. Le carbure haute qualité et les tranchants polis permettent d‘atteindre des durées d‘usage élevées et de réaliser un perçage fiable pour les grandes séries. NEU / NEW / NOUVEAU ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 39 615-617 VHM-NC-Anbohrer Durchmesser hinterschliffen Serie 615: Spitzenwinkel 90° Serie 616: Spitzenwinkel 120° Serie 617: Spitzenwinkel 142° Ausführung: 2 Schneiden Schnittrichtung: rechts Anschnitt: Kegelmantelschliff ausgespitzt HM-Sorte: EZ21 Geometrie und Hartmetall speziell ausgelegt zum Zentrieren in Stahl, Titan und Buntmetallen. Auch geeignet zum Ansenken und Bohren. 615 - 90° Solid carbide NC spot drills Bestell-Nr. d l1 order no N° référence Series 615: point angle 90° Series 616: point angle 120° Series 617: point angle 142° 615.020 615.030 615.040 615.050 615.060 615.080 615.100 615.120 diameter relief ground Design: 2 flutes Cutting: RH Chamfer: cone-surface cut, picked out Carbide grade: EZ21 Geometry and carbide specially designed for centring in steel, titanium and non-ferrous metals. Also suited for counter-sinking and drilling. Foret à pointer NC en carbure 2,0 3,0 4,0 5,0 6,0 8,0 10,0 12,0 8 9 10 10 10 14 16 18 l 40 40 45 45 45 50 60 60 616 - 120° Bestell-Nr. d l1 l order no N° référence 616.020 616.030 616.040 616.050 616.060 616.080 616.100 616.120 2,0 3,0 4,0 5,0 6,0 8,0 10,0 12,0 8 9 10 10 10 14 16 18 40 40 45 45 45 50 60 60 avec dépouille sur le diamètre Série 615: Angle de pointe 90° Série 616: Angle de pointe 120° Série 617: Angle de pointe 142° Modèle: 2 dents Sens de coupe: à droite Affûtage: rectification de la pointe à 90° tronconique et âme amincie Nuance de carbure: EZ21 Géométrie et carbure conçus pour le centrage dans l'acier, du titane et métaux non ferreux. Egalement approprié pour le lamage et le perçage. 40 617 - 142° Bestell-Nr. d l1 l order no N° référence 617.080 617.140 8,0 14,0 14 20 50 70 Auf Anfrage auch mit Beschichtung lieferbar. Also available with coating. Livrable aussi avec revêtement, sur demande ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 620 VHM-Spiralbohrer Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Hartmetall-Spiralbohrer für Stahl und Buntmetalle. Zwischenabmessungen auf Anfrage. Verpackungseinheit: 5 Stück Solid carbide twist drills Design: 2 flutes Cutting: RH Helix angle: 30° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 Solid carbide twist drills for steel and nonferrous metals. Intermediate sizes on request. Packing unit: 5 pieces Foret hélicoïdal en carbure Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Foret hélicoïdal en carbure pour l'acier et les métaux non ferreux. Dimensions intermédiaires sur demande. Conditionnement par 5. Bestell-Nr. order no N° référence 620.0030 620.0035 620.0040 620.0045 620.0050 620.0055 620.0060 620.0065 620.0070 620.0075 620.0080 620.0085 620.0090 620.0095 620.0100 620.0105 620.0110 620.0115 620.0120 620.0125 620.0130 620.0135 620.0140 620.0145 620.0150 620.0155 620.0160 620.0165 620.0170 620.0175 620.0180 620.0185 620.0190 620.0195 620.0200 620.0205 620.0210 620.0215 620.0220 620.0225 620.0230 620.0235 620.0240 620.0245 620.0250 620.0255 d l1 l 0,30 0,35 0,40 0,45 0,50 0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1,00 1,05 1,10 1,15 1,20 1,25 1,30 1,35 1,40 1,45 1,50 1,55 1,60 1,65 1,70 1,75 1,80 1,85 1,90 1,95 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 4,0 5,0 5,0 5,0 5,0 5,0 5,5 5,0 6,0 8,0 8,0 9,0 9,0 10,0 6,0 10,0 7,0 10,0 8,0 12,0 8,0 12,0 9,0 12,0 9,0 16,0 10,0 16,0 10,0 16,0 11,0 16,0 11,0 16,0 12,0 18,0 12,0 18,0 13,0 18,0 13,0 18,0 14,0 18,0 14,0 18,0 28 30 30 30 30 30 30 30 30 30 30 30 30 30 26 30 28 30 30 30 30 30 32 32 32 34 34 40 34 40 36 40 36 40 38 40 38 40 40 40 40 40 43 43 43 45 Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 41 620 VHM-Spiralbohrer Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Hartmetall-Spiralbohrer für Stahl und Buntmetalle. Zwischenabmessungen auf Anfrage. Verpackungseinheit: 5 Stück Solid carbide twist drills Design: 2 flutes Cutting: RH Helix angle: 30° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 Solid carbide twist drills for steel and nonferrous metals. Intermediate sizes on request. Packing unit: 5 pieces Foret hélicoïdal en carbure Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Foret hélicoïdal en carbure pour l'acier et les métaux non ferreux. Dimensions intermédiaires sur demande. Conditionnement par 5. Bestell-Nr. order no N° référence 620.0260 620.0265 620.0270 620.0275 620.0280 620.0285 620.0290 620.0295 620.0300 620.0305 620.0310 620.0315 620.0320 620.0325 620.0330 620.0335 620.0340 620.0345 620.0350 620.0355 620.0360 620.0365 620.0370 620.0375 620.0380 620.0385 620.0390 620.0395 620.0400 620.0405 620.0410 620.0415 620.0420 620.0425 620.0430 620.0435 620.0440 620.0445 620.0450 620.0455 620.0460 620.0465 620.0470 620.0475 620.0480 620.0485 d l1 l 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 3,00 3,05 3,10 3,15 3,20 3,25 3,30 3,35 3,40 3,45 3,50 3,55 3,60 3,65 3,70 3,75 3,80 3,85 3,90 3,95 4,00 4,05 4,10 4,15 4,20 4,25 4,30 4,35 4,40 4,45 4,50 4,55 4,60 4,65 4,70 4,75 4,80 4,85 14,0 18,0 16,0 20,0 16,0 20,0 16,0 20,0 16,0 22,0 18,0 22,0 18,0 20,0 18,0 22,0 20,0 22,0 20,0 22,0 20,0 22,0 20,0 22,0 22,0 22,0 22,0 22,0 22,0 25,0 22,0 25,0 22,0 25,0 24,0 25,0 24,0 25,0 24,0 25,0 24,0 25,0 24,0 26,0 26,0 26,0 43 45 46 46 46 45 46 45 46 49 49 50 49 50 49 50 52 50 52 50 52 50 52 50 50 50 55 50 55 50 55 60 55 60 58 60 58 60 58 60 58 60 58 60 62 60 Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. 42 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 620 VHM-Spiralbohrer Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Hartmetall-Spiralbohrer für Stahl und Buntmetalle. Zwischenabmessungen auf Anfrage. Verpackungseinheit: 5 Stück Solid carbide twist drills Design: 2 flutes Cutting: RH Helix angle: 30° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 Solid carbide twist drills for steel and nonferrous metals. Intermediate sizes on request. Packing unit: 5 pieces Foret hélicoïdal en carbure Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Foret hélicoïdal en carbure pour l'acier et les métaux non ferreux. Dimensions intermédiaires sur demande. Conditionnement par 5. Bestell-Nr. order no N° référence 620.0490 620.0495 620.0500 620.0505 620.0510 620.0515 620.0520 620.0525 620.0530 620.0535 620.0540 620.0545 620.0550 620.0555 620.0560 620.0565 620.0570 620.0575 620.0580 620.0585 620.0590 620.0595 620.0600 620.0610 620.0620 620.0630 620.0640 620.0650 620.0660 620.0670 620.0680 620.0690 620.0700 620.0710 620.0720 620.0730 620.0740 620.0750 620.0760 620.0770 620.0780 620.0790 620.0800 d l1 l 4,90 4,95 5,00 5,05 5,10 5,15 5,20 5,25 5,30 5,35 5,40 5,45 5,50 5,55 5,60 5,65 5,70 5,75 5,80 5,85 5,90 5,95 6,00 6,10 6,20 6,30 6,40 6,50 6,60 6,70 6,80 6,90 7,00 7,10 7,20 7,30 7,40 7,50 7,60 7,70 7,80 7,90 8,00 26,0 26,0 26,0 26,0 26,0 26,0 26,0 26,0 26,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 28,0 31,0 31,0 31,0 31,0 31,0 31,0 31,0 34,0 34,0 34,0 34,0 34,0 34,0 34,0 34,0 37,0 37,0 37,0 37,0 37,0 62 60 60 60 62 60 62 60 62 60 66 60 66 60 66 60 66 60 66 60 66 60 66 70 70 70 70 70 70 70 74 74 74 74 74 74 74 74 79 79 79 79 79 Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 43 622 VHM-Spiralbohrer nach DIN 338 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Hartmetall-Spiralbohrer für Stahl und Buntmetalle. Zwischenabmessungen auf Anfrage. Ø 0,50 - 6,0 mm: Verpackungseinheit: 5 Stück Bestell-Nr. d l 1 order no N° référence Solid carbide twist drills as per DIN 338 Design: 2 flutes Cutting: RH Helix angle: 30° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 Solid carbide twist drills for steel and nonferrous metals. Intermediate sizes on request. Ø 0,50 - 6,0 mm: Packing unit: 5 pieces Foret hélicoïdal en carbure selon DIN 338 Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Foret hélicoïdal en carbure pour l'acier et les métaux non ferreux. Dimensions intermédiaires sur demande. Ø 0,50 - 6,0 mm: Conditionnement par 5. 622.0050 622.0060 622.0070 622.0080 622.0090 622.0100 622.0110 622.0120 622.0130 622.0140 622.0150 622.0160 622.0170 622.0180 622.0190 622.0200 622.0210 622.0220 622.0230 622.0240 622.0250 622.0260 622.0270 622.0280 622.0290 622.0300 622.0310 622.0320 622.0330 622.0340 622.0350 622.0360 622.0370 622.0380 622.0390 622.0400 622.0410 622.0420 622.0430 622.0440 622.0450 622.0460 622.0470 622.0480 622.0490 622.0500 622.0510 622.0520 622.0530 622.0540 0,50 0,60 0,70 0,80 0,90 1,00 1,10 1,20 1,30 1,40 1,50 1,60 1,70 1,80 1,90 2,00 2,10 2,20 2,30 2,40 2,50 2,60 2,70 2,80 2,90 3,00 3,10 3,20 3,30 3,40 3,50 3,60 3,70 3,80 3,90 4,00 4,10 4,20 4,30 4,40 4,50 4,60 4,70 4,80 4,90 5,00 5,10 5,20 5,30 5,40 l 6 7 9 10 11 12 14 16 16 18 18 20 20 22 22 22 24 27 27 30 30 30 33 33 33 33 36 36 36 39 39 39 39 43 43 43 43 43 47 47 47 47 47 52 52 52 52 52 52 57 22 24 28 30 32 34 36 38 38 40 40 43 43 46 46 49 49 53 53 57 57 57 61 61 61 61 65 65 65 70 70 70 70 75 75 75 75 75 80 80 80 80 80 86 86 86 86 86 86 93 Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. 44 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 622 VHM-Spiralbohrer nach DIN 338 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Hartmetall-Spiralbohrer für Stahl und Buntmetalle. Zwischenabmessungen auf Anfrage. Ø 0,50 - 6,0 mm: Verpackungseinheit: 5 Stück Bestell-Nr. d l 1 l order no N° référence Solid carbide twist drills as per DIN 338 Design: 2 flutes Cutting: RH Helix angle: 30° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 Solid carbide twist drills for steel and nonferrous metals. Intermediate sizes on request. 622.0550 622.0600 622.0650 622.0700 622.0750 622.0800 622.0850 622.0900 622.0950 622.1000 622.1050 622.1100 622.1150 622.1200 5,50 6,00 6,50 7,00 7,50 8,00 8,50 9,00 9,50 10,00 10,50 11,00 11,50 12,00 57 57 63 69 69 75 75 81 81 87 87 94 94 101 93 93 101 109 109 117 117 125 125 133 133 142 142 151 Ø 0,50 - 6,0 mm: Packing unit: 5 pieces Foret hélicoïdal en carbure selon DIN 338 Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Foret hélicoïdal en carbure pour l'acier et les métaux non ferreux. Dimensions intermédiaires sur demande. Ø 0,50 - 6,0 mm: Conditionnement par 5. Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 45 629 VHM-Spiralbohrer mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30° Spitzenwinkel: 120° Anschnitt: 4 Flächen HM-Sorte: EZ 21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Verpackungseinheit: 5 Stück Beschichtung auf Anfrage Solid carbide twist drill with reinforced shank Design: 2 flutes Cutting: RH Helix angle: 30° Point angle: 120° Chamfer: 4 facet pointing Carbide grade: EZ21 Geometry and carbide designed for microprocessing. Packing unit: 5 pieces. Coating on demand. Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30° Angle de pointe: 120° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Conditionnement par 5. Revêtement sur demande. Bestell-Nr. order no N° référence 629.010 629.011 629.012 629.013 629.014 629.015 629.016 629.017 629.018 629.019 629.020 629.021 629.022 629.023 629.024 629.025 629.026 629.027 629.028 629.029 629.030 629.031 629.032 629.033 629.034 629.035 629.036 629.037 629.038 629.039 629.040 629.041 629.042 629.043 629.044 629.045 629.046 629.047 629.048 629.049 629.050 629.051 629.052 629.053 629.054 629.055 629.056 629.057 629.058 629.059 d1 l1 l d 0,10 0,11 0,12 0,13 0,14 0,15 0,16 0,17 0,18 0,19 0,20 0,21 0,22 0,23 0,24 0,25 0,26 0,27 0,28 0,29 0,30 0,31 0,32 0,33 0,34 0,35 0,36 0,37 0,38 0,39 0,40 0,41 0,42 0,43 0,44 0,45 0,46 0,47 0,48 0,49 0,50 0,51 0,52 0,53 0,54 0,55 0,56 0,57 0,58 0,59 0,70 0,77 0,84 0,91 0,98 1,05 1,12 1,19 1,26 1,33 1,40 1,47 1,54 1,61 1,68 1,75 1,82 1,89 1,96 2,03 2,10 2,17 2,24 2,31 2,38 2,45 2,52 2,59 2,66 2,73 2,80 2,87 2,94 3,01 3,08 3,15 3,22 3,29 3,36 3,43 3,50 3,57 3,64 3,71 3,78 3,85 3,92 3,99 4,06 4,13 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 NEU / NEW / NOUVEAU 46 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 629 VHM-Spiralbohrer mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30° Spitzenwinkel: 120° Anschnitt: 4 Flächen HM-Sorte: EZ 21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Verpackungseinheit: 5 Stück Beschichtung auf Anfrage Solid carbide twist drill with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 30° Point angle: 120° Chamfer: 4 facet pointing Carbide grade: EZ21 629.060 629.061 629.062 629.063 629.064 629.065 629.066 629.067 629.068 629.069 629.070 629.071 629.072 629.073 629.074 629.075 629.076 629.077 629.078 629.079 629.080 629.081 629.082 629.083 629.084 629.085 629.086 629.087 629.088 629.089 629.090 629.091 629.092 629.093 629.094 629.095 629.096 629.097 629.098 629.099 629.100 629.101 629.102 629.103 629.104 629.105 629.106 629.107 629.108 629.109 Geometry and carbide designed for microprocessing. Packing unit: 5 pieces. Coating on demand. Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30° Angle de pointe: 120° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Conditionnement par 5. Revêtement sur demande. d1 l1 l d 0,60 0,61 0,62 0,63 0,64 0,65 0,66 0,67 0,68 0,69 0,70 0,71 0,72 0,73 0,74 0,75 0,76 0,77 0,78 0,79 0,80 0,81 0,82 0,83 0,84 0,85 0,86 0,87 0,88 0,89 0,90 0,91 0,92 0,93 0,94 0,95 0,96 0,97 0,98 0,99 1,00 1,01 1,02 1,03 1,04 1,05 1,06 1,07 1,08 1,09 4,20 4,27 4,34 4,41 4,48 4,55 4,62 4,69 4,76 4,83 4,90 4,97 5,04 5,11 5,18 5,25 5,32 5,39 5,46 5,53 5,60 5,67 5,74 5,81 5,88 5,95 6,02 6,09 6,16 6,23 6,30 6,37 6,44 6,51 6,58 6,65 6,72 6,79 6,86 6,93 7,00 7,07 7,14 7,21 7,28 7,35 7,42 7,49 7,56 7,63 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 NEU / NEW / NOUVEAU ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 47 629 VHM-Spiralbohrer mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30° Spitzenwinkel: 120° Anschnitt: 4 Flächen HM-Sorte: EZ 21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Verpackungseinheit: 5 Stück Beschichtung auf Anfrage Solid carbide twist drill with reinforced shank Design: 2 flutes Cutting: RH Helix angle: 30° Point angle: 120° Chamfer: 4 facet pointing Carbide grade: EZ21 Geometry and carbide designed for microprocessing. Packing unit: 5 pieces. Coating on demand. Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30° Angle de pointe: 120° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Conditionnement par 5. Revêtement sur demande. Bestell-Nr. order no N° référence 629.110 629.111 629.112 629.113 629.114 629.115 629.116 629.117 629.118 629.119 629.120 629.121 629.122 629.123 629.124 629.125 629.126 629.127 629.128 629.129 629.130 629.131 629.132 629.133 629.134 629.135 629.136 629.137 629.138 629.139 629.140 629.141 629.142 629.143 629.144 629.145 629.146 629.147 629.148 629.149 629.150 629.151 629.152 629.153 629.154 629.155 629.156 629.157 629.158 629.159 d1 l1 l d 1,10 1,11 1,12 1,13 1,14 1,15 1,16 1,17 1,18 1,19 1,20 1,21 1,22 1,23 1,24 1,25 1,26 1,27 1,28 1,29 1,30 1,31 1,32 1,33 1,34 1,35 1,36 1,37 1,38 1,39 1,40 1,41 1,42 1,43 1,44 1,45 1,46 1,47 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,55 1,56 1,57 1,58 1,59 7,70 7,77 7,84 7,91 7,98 8,05 8,12 8,19 8,26 8,33 8,40 8,47 8,54 8,61 8,68 8,75 8,82 8,89 8,96 9,03 9,10 9,17 9,24 9,31 9,38 9,45 9,52 9,59 9,66 9,73 9,80 9,87 9,94 10,01 10,08 10,15 10,22 10,29 10,36 10,43 10,50 10,57 10,64 10,71 10,78 10,85 10,92 10,99 11,06 11,13 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 NEU / NEW / NOUVEAU 48 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 629 VHM-Spiralbohrer mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30° Spitzenwinkel: 120° Anschnitt: 4 Flächen HM-Sorte: EZ 21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Verpackungseinheit: 5 Stück Beschichtung auf Anfrage Solid carbide twist drill with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 30° Point angle: 120° Chamfer: 4 facet pointing Carbide grade: EZ21 629.160 629.161 629.162 629.163 629.164 629.165 629.166 629.167 629.168 629.169 629.170 629.171 629.172 629.173 629.174 629.175 629.176 629.177 629.178 629.179 629.180 629.181 629.182 629.183 629.184 629.185 629.186 629.187 629.188 629.189 629.190 629.191 629.192 629.193 629.194 629.195 629.196 629.197 629.198 629.199 629.200 Geometry and carbide designed for microprocessing. Packing unit: 5 pieces. Coating on demand. Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30° Angle de pointe: 120° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. d1 l1 l d 1,60 1,61 1,62 1,63 1,64 1,65 1,66 1,67 1,68 1,69 1,70 1,71 1,72 1,73 1,74 1,75 1,76 1,77 1,78 1,79 1,80 1,81 1,82 1,83 1,84 1,85 1,86 1,87 1,88 1,89 1,90 1,91 1,92 1,93 1,94 1,95 1,96 1,97 1,98 1,99 2,00 11,20 11,27 11,34 11,41 11,48 11,55 11,62 11,69 11,76 11,83 11,90 11,97 12,04 12,11 12,18 12,25 12,32 12,39 12,46 12,53 12,60 12,67 12,74 12,81 12,88 12,95 13,02 13,09 13,16 13,23 13,30 13,37 13,44 13,51 13,58 13,65 13,72 13,79 13,86 13,93 14,00 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Conditionnement par 5. Revêtement sur demande. NEU / NEW / NOUVEAU ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 49 630 VHM-Spiralbohrer, kurz, mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 24° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Verpackungseinheit: 5 Stück Solid carbide twist drills with reinforced shank, short Bestell-Nr. d1 l1 l d order no N° référence Design: 2 flutes Cutting: RH Helix angle: 24° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 630.050 630.051 630.052 630.053 630.054 630.055 630.056 630.057 630.058 630.059 630.060 630.061 630.062 630.063 630.064 630.065 630.066 630.067 630.068 630.069 630.070 630.071 630.072 630.073 630.074 630.075 630.076 630.077 630.078 630.079 630.080 630.081 630.082 630.083 630.084 630.085 630.086 630.087 630.088 630.089 630.090 630.091 630.092 630.093 630.094 630.095 Geometry and carbide designed for microprocessing. Packing unit: 5 pieces Foret hélicoïdal court en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 24° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Conditionnement par 5. 0,50 0,51 0,52 0,53 0,54 0,55 0,56 0,57 0,58 0,59 0,60 0,61 0,62 0,63 0,64 0,65 0,66 0,67 0,68 0,69 0,70 0,71 0,72 0,73 0,74 0,75 0,76 0,77 0,78 0,79 0,80 0,81 0,82 0,83 0,84 0,85 0,86 0,87 0,88 0,89 0,90 0,91 0,92 0,93 0,94 0,95 1,4 1,4 1,4 1,4 1,4 1,4 1,5 1,5 1,5 1,5 1,5 1,6 1,6 1,6 1,6 1,6 1,8 1,8 1,8 1,8 1,8 1,9 1,9 1,9 1,9 1,9 2,0 2,0 2,0 2,0 2,0 2,1 2,1 2,1 2,1 2,1 2,3 2,3 2,3 2,3 2,3 2,4 2,4 2,4 2,4 2,4 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. 50 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 630 VHM-Spiralbohrer, kurz, mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 24° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Verpackungseinheit: 5 Stück Solid carbide twist drills with reinforced shank, short Design: 2 flutes Cutting: RH Helix angle: 24° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 Geometry and carbide designed for microprocessing. Packing unit: 5 pieces Foret hélicoïdal court en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 24° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Conditionnement par 5. l1 l Bestell-Nr. d1 order no N° référence 630.096 630.097 630.098 630.099 630.100 630.101 630.102 630.103 630.104 630.105 630.106 630.107 630.108 630.109 630.110 630.111 630.112 630.113 630.114 630.115 630.116 630.117 630.118 630.119 630.120 630.121 630.122 630.123 630.124 630.125 630.126 630.127 630.128 630.129 630.130 630.131 630.132 630.133 630.134 630.135 630.136 630.137 630.138 630.139 630.140 630.141 0,96 0,97 0,98 0,99 1,00 1,01 1,02 1,03 1,04 1,05 1,06 1,07 1,08 1,09 1,10 1,11 1,12 1,13 1,14 1,15 1,16 1,17 1,18 1,19 1,20 1,21 1,22 1,23 1,24 1,25 1,26 1,27 1,28 1,29 1,30 1,31 1,32 1,33 1,34 1,35 1,36 1,37 1,38 1,39 1,40 1,41 2,5 2,5 2,5 2,5 2,5 2,6 2,6 2,6 2,6 2,6 2,8 2,8 2,8 2,8 2,8 2,9 2,9 2,9 2,9 2,9 3,0 3,0 3,0 3,0 3,0 3,1 3,1 3,1 3,1 3,1 3,3 3,3 3,3 3,3 3,3 3,4 3,4 3,4 3,4 3,4 3,5 3,5 3,5 3,5 3,5 3,6 d 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 51 630 VHM-Spiralbohrer, kurz, mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 24° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Verpackungseinheit: 5 Stück Solid carbide twist drills with reinforced shank, short Bestell-Nr. d1 l1 l d order no N° référence Design: 2 flutes Cutting: RH Helix angle: 24° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 630.142 630.143 630.144 630.145 630.146 630.147 630.148 630.149 630.150 630.151 630.152 630.153 630.154 630.155 630.156 630.157 630.158 630.159 630.160 630.161 630.162 630.163 630.164 630.165 630.166 630.167 630.168 630.169 630.170 630.171 630.172 630.173 630.174 630.175 630.176 630.177 630.178 630.179 630.180 630.181 630.182 630.183 630.184 630.185 630.186 630.187 Geometry and carbide designed for microprocessing. Packing unit: 5 pieces Foret hélicoïdal court en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 24° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Conditionnement par 5. 1,42 1,43 1,44 1,45 1,46 1,47 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,55 1,56 1,57 1,58 1,59 1,60 1,61 1,62 1,63 1,64 1,65 1,66 1,67 1,68 1,69 1,70 1,71 1,72 1,73 1,74 1,75 1,76 1,77 1,78 1,79 1,80 1,81 1,82 1,83 1,84 1,85 1,86 1,87 3,6 3,6 3,6 3,6 3,8 3,8 3,8 3,8 3,8 3,9 3,9 3,9 3,9 3,9 4,0 4,0 4,0 4,0 4,0 4,1 4,1 4,1 4,1 4,1 4,3 4,3 4,3 4,3 4,3 4,4 4,4 4,4 4,4 4,4 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 30 30 30 30 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. 52 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 630 VHM-Spiralbohrer, kurz, mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 24° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Verpackungseinheit: 5 Stück Solid carbide twist drills with reinforced shank, short Bestell-Nr. d1 l1 l order no N° référence Design: 2 flutes Cutting: RH Helix angle: 24° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 630.188 630.189 630.190 630.191 630.192 630.193 630.194 630.195 630.196 630.197 630.198 630.199 630.200 630.205 630.210 630.215 630.220 630.225 630.230 630.235 630.240 630.245 630.250 630.255 630.260 630.265 630.270 630.275 630.280 630.285 630.290 630.295 Geometry and carbide designed for microprocessing. Packing unit: 5 pieces Foret hélicoïdal court en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 24° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 1,88 1,89 1,90 1,91 1,92 1,93 1,94 1,95 1,96 1,97 1,98 1,99 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 d 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Géométrie et sorte de carbure conçus pour le micro-usinage. Conditionnement par 5. Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 53 631 VHM-Spiralbohrer, lang, mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 24°/30° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Bestellbeispiel: 631.xxx.24° 631.xxx.30° Verpackungseinheit: 5 Stück 24° Solid carbide twist drills with reinforced shank, long Bestell-Nr. d 1 l1 l order no N° référence Design: 2 flutes Cutting: RH Helix angle: 24°/30° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 631.010 631.011 631.012 631.013 631.014 631.015 631.016 631.017 631.018 631.019 631.020 631.021 631.022 631.023 631.024 631.025 631.026 631.027 631.028 631.029 631.030 631.031 631.032 631.033 631.034 631.035 631.036 631.037 631.038 631.039 631.040 631.041 631.042 631.043 631.044 631.045 631.046 631.047 631.048 631.049 631.050 631.051 631.052 631.053 631.054 631.055 Geometry and carbide designed for microprocessing. Special coatings for optimum results with special materials. Ordering example: 631.xxx.24° 631.xxx.30° Packing unit: 5 pieces Foret hélicoïdal long en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 24°/30° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Revêtement conçu pour résultats optimaux dans matières spéciales. Exemple de commande : 631.xxx.24° 631.xxx.30° 0,10 0,11 0,12 0,13 0,14 0,15 0,16 0,17 0,18 0,19 0,20 0,21 0,22 0,23 0,24 0,25 0,26 0,27 0,28 0,29 0,30 0,31 0,32 0,33 0,34 0,35 0,36 0,37 0,38 0,39 0,40 0,41 0,42 0,43 0,44 0,45 0,46 0,47 0,48 0,49 0,50 0,51 0,52 0,53 0,54 0,55 0,6 0,6 0,6 0,8 0,8 0,8 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2,0 2,0 2,0 2,0 2,0 3,5 3,5 3,5 3,5 4,0 4,0 4,0 4,0 4,0 4,5 4,5 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30° d 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Conditionnement par 5. Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. 54 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 631 VHM-Spiralbohrer, lang, mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 24°/30° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Bestellbeispiel: 631.xxx.24° 631.xxx.30° Verpackungseinheit: 5 Stück 24° 30° 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Solid carbide twist drills with reinforced shank, long Bestell-Nr. d 1 l1 l d order no N° référence Design: 2 flutes Cutting: RH Helix angle: 24°/30° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 631.056 631.057 631.058 631.059 631.060 631.061 631.062 631.063 631.064 631.065 631.066 631.067 631.068 631.069 631.070 631.071 631.072 631.073 631.074 631.075 631.076 631.077 631.078 631.079 631.080 631.081 631.082 631.083 631.084 631.085 631.086 631.087 631.088 631.089 631.090 631.091 631.092 631.093 631.094 631.095 631.096 631.097 631.098 631.099 631.100 631.101 Geometry and carbide designed for microprocessing. Special coatings for optimum results with special materials. Ordering example: 631.xxx.24° 631.xxx.30° Packing unit: 5 pieces Foret hélicoïdal long en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 24°/30° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Revêtement conçu pour résultats optimaux dans matières spéciales. Exemple de commande : 631.xxx.24° 631.xxx.30° 0,56 0,57 0,58 0,59 0,60 0,61 0,62 0,63 0,64 0,65 0,66 0,67 0,68 0,69 0,70 0,71 0,72 0,73 0,74 0,75 0,76 0,77 0,78 0,79 0,80 0,81 0,82 0,83 0,84 0,85 0,86 0,87 0,88 0,89 0,90 0,91 0,92 0,93 0,94 0,95 0,96 0,97 0,98 0,99 1,00 1,01 4,5 4,5 4,5 4,5 4,5 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,5 5,6 5,6 5,6 5,6 5,6 5,6 5,6 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 8,0 8,0 8,0 8,0 9,0 9,0 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 Conditionnement par 5. Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 55 631 VHM-Spiralbohrer, lang, mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 24°/30° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Bestellbeispiel: 631.xxx.24° 631.xxx.30° Verpackungseinheit: 5 Stück 24° Solid carbide twist drills with reinforced shank, long Bestell-Nr. d 1 l1 l d order no N° référence Design: 2 flutes Cutting: RH Helix angle: 24°/30° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 631.102 631.103 631.104 631.105 631.106 631.107 631.108 631.109 631.110 631.111 631.112 631.113 631.114 631.115 631.116 631.117 631.118 631.119 631.120 631.121 631.122 631.123 631.124 631.125 631.126 631.127 631.128 631.129 631.130 631.131 631.132 631.133 631.134 631.135 631.136 631.137 631.138 631.139 631.140 631.141 631.142 631.143 631.144 631.145 631.146 631.147 Geometry and carbide designed for microprocessing. Special coatings for optimum results with special materials. Ordering example: 631.xxx.24° 631.xxx.30° Packing unit: 5 pieces Foret hélicoïdal long en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 24°/30° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Revêtement conçu pour résultats optimaux dans matières spéciales. Exemple de commande : 631.xxx.24° 631.xxx.30° 1,02 1,03 1,04 1,05 1,06 1,07 1,08 1,09 1,10 1,11 1,12 1,13 1,14 1,15 1,16 1,17 1,18 1,19 1,20 1,21 1,22 1,23 1,24 1,25 1,26 1,27 1,28 1,29 1,30 1,31 1,32 1,33 1,34 1,35 1,36 1,37 1,38 1,39 1,40 1,41 1,42 1,43 1,44 1,45 1,46 1,47 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 30° * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Conditionnement par 5. Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. 56 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 631 VHM-Spiralbohrer, lang, mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 24°/30° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Bestellbeispiel: 631.xxx.24° 631.xxx.30° Verpackungseinheit: 5 Stück 24° Solid carbide twist drills with reinforced shank, long Bestell-Nr. d 1 l1 l d order no N° référence Design: 2 flutes Cutting: RH Helix angle: 24°/30° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 631.148 631.149 631.150 631.151 631.152 631.153 631.154 631.155 631.156 631.157 631.158 631.159 631.160 631.161 631.162 631.163 631.164 631.165 631.166 631.167 631.168 631.169 631.170 631.171 631.172 631.173 631.174 631.175 631.176 631.177 631.178 631.179 631.180 631.181 631.182 631.183 631.184 631.185 631.186 631.187 631.188 631.189 631.190 631.191 631.192 631.193 Geometry and carbide designed for microprocessing. Special coatings for optimum results with special materials. Ordering example: 631.xxx.24° 631.xxx.30° Packing unit: 5 pieces Foret hélicoïdal long en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 24°/30° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Revêtement conçu pour résultats optimaux dans matières spéciales. Exemple de commande : 631.xxx.24° 631.xxx.30° 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,55 1,56 1,57 1,58 1,59 1,60 1,61 1,62 1,63 1,64 1,65 1,66 1,67 1,68 1,69 1,70 1,71 1,72 1,73 1,74 1,75 1,76 1,77 1,78 1,79 1,80 1,81 1,82 1,83 1,84 1,85 1,86 1,87 1,88 1,89 1,90 1,91 1,92 1,93 11,5 11,5 11,5 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 30 30 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 1,5 1,5 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 30° * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Conditionnement par 5. Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 57 631 VHM-Spiralbohrer, lang, mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 24°/30° Spitzenwinkel: 118° Anschnitt: 4 Flächen HM-Sorte: EZ21 Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung. Bestellbeispiel: 631.xxx.24° 631.xxx.30° Verpackungseinheit: 5 Stück 24° Solid carbide twist drills with reinforced shank, long Bestell-Nr. d 1 l1 l d order no N° référence Design: 2 flutes Cutting: RH Helix angle: 24°/30° Point angle: 118° Chamfer: 4 facet pointing Carbide grade: EZ21 631.194 631.195 631.196 631.197 631.198 631.199 631.200 631.205 631.210 631.215 631.220 631.225 631.230 631.235 631.240 631.245 631.250 631.255 631.260 631.265 631.270 631.275 631.280 631.285 631.290 631.295 Geometry and carbide designed for microprocessing. Special coatings for optimum results with special materials. Ordering example: 631.xxx.24° 631.xxx.30° Packing unit: 5 pieces Foret hélicoïdal long en carbure avec manche renforcé 1,94 1,95 1,96 1,97 1,98 1,99 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 2,0 2,0 2,0 2,0 2,0 2,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 30° * * * * * * * * * * * * * * * * * * * * * * * * * * Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 24°/30° Angle de pointe: 118° Affûtage: 4 facettes Sorte de carbure: EZ21 Géométrie et sorte de carbure conçus pour le micro-usinage. Revêtement conçu pour résultats optimaux dans matières spéciales. Exemple de commande : 631.xxx.24° 631.xxx.30° Conditionnement par 5. Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. 58 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 632 VHM-Spiralbohrer mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° Spitzenwinkel: 130° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Standard Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Titan, Edelstahl und härtere Materialien. Durch Ausspitzung selbstzentrierend und Reduzierung der Prozesswärme. Mit TiAlN-Beschichtung erhältlich für optimale Ergebnisse bei Sonderwerkstoffen. Bestellbeispiel: 632.030.TIALN Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 35° Point angle: 130° Chamfer: 4 facet pointing Carbide grade: EZ21 Point: Standard 632.030 632.031* 632.032* 632.033* 632.034* 632.035 632.036* 632.037* 632.038* 632.039* 632.040 632.041* 632.042* 632.043* 632.044 632.045 632.046* 632.047* 632.048* 632.049* 632.050 632.051* 632.052* 632.053* 632.054* 632.055 632.056* 632.057* 632.058* 632.059* 632.060 632.061* 632.062* 632.063* 632.064* 632.065 632.066* 632.067* 632.068 632.069* 632.070 632.071* 632.072* 632.073* 632.074* 632.075 632.076* Geometry and carbide designed for microprocessing of titanium, stainless steel, and harder materials. With point for self-centering and reduction of process heat. Available with TiAlN coating for optimum results when working with special materials. Ordering example: 632.030.TIALN Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° Angle de pointe: 130° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: standard Géométrie et sorte de carbure conçus pour le micro-usinage du titane, des aciers spéciaux et autres matériaux plus durs. Autocentrant et réduction de la chaleur du processus grâce à l'affûtage en pointe. d1 l1 l d 0,30 0,31 0,32 0,33 0,34 0,35 0,36 0,37 0,38 0,39 0,40 0,41 0,42 0,43 0,44 0,45 0,46 0,47 0,48 0,49 0,50 0,51 0,52 0,53 0,54 0,55 0,56 0,57 0,58 0,59 0,60 0,61 0,62 0,63 0,64 0,65 0,66 0,67 0,68 0,69 0,70 0,71 0,72 0,73 0,74 0,75 0,76 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2,0 2,0 2,0 2,0 2,0 3,5 3,5 3,5 3,5 4,0 4,0 4,0 4,0 4,0 4,5 4,5 4,5 4,5 4,5 4,5 4,5 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,5 5,6 5,6 5,6 5,6 5,6 5,6 5,6 6,5 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Revêtement TiAlN pour résultats optimaux dans matières spéciales. Exemple de commande: 632.032.TIALN Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 59 632 VHM-Spiralbohrer mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° Spitzenwinkel: 130° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Standard Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Titan, Edelstahl und härtere Materialien. Durch Ausspitzung selbstzentrierend und Reduzierung der Prozesswärme. Mit TiAlN-Beschichtung erhältlich für optimale Ergebnisse bei Sonderwerkstoffen. Bestellbeispiel: 632.030.TIALN Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 35° Point angle: 130° Chamfer: 4 facet pointing Carbide grade: EZ21 Point: Standard 632.077 632.078 632.079 632.080 632.081 632.082 632.083* 632.084* 632.085 632.086* 632.087* 632.088* 632.089* 632.090 632.091* 632.092* 632.093* 632.094* 632.095 632.096 632.097 632.098 632.099 632.100 632.101 632.102* 632.103 632.104 632.105 632.106* 632.107 632.108 632.109 632.110 632.111* 632.112 632.113 632.114 632.115 632.116 632.117* 632.118* 632.119* 632.120 632.121* 632.122 632.123* Geometry and carbide designed for microprocessing of titanium, stainless steel, and harder materials. With point for self-centering and reduction of process heat. Available with TiAlN coating for optimum results when working with special materials. Ordering example: 632.030.TIALN Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° Angle de pointe: 130° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: standard Géométrie et sorte de carbure conçus pour le micro-usinage du titane, des aciers spéciaux et autres matériaux plus durs. Autocentrant et réduction de la chaleur du processus grâce à l'affûtage en pointe. d1 l1 l d 0,77 0,78 0,79 0,80 0,81 0,82 0,83 0,84 0,85 0,86 0,87 0,88 0,89 0,90 0,91 0,92 0,93 0,94 0,95 0,96 0,97 0,98 0,99 1,00 1,01 1,02 1,03 1,04 1,05 1,06 1,07 1,08 1,09 1,10 1,11 1,12 1,13 1,14 1,15 1,16 1,17 1,18 1,19 1,20 1,21 1,22 1,23 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 6,5 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 8,0 8,0 8,0 8,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 10,0 10,0 10,0 10,0 10,0 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Revêtement TiAlN pour résultats optimaux dans matières spéciales. Exemple de commande: 632.032.TIALN 60 Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 632 VHM-Spiralbohrer mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° Spitzenwinkel: 130° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Standard Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Titan, Edelstahl und härtere Materialien. Durch Ausspitzung selbstzentrierend und Reduzierung der Prozesswärme. Mit TiAlN-Beschichtung erhältlich für optimale Ergebnisse bei Sonderwerkstoffen. Bestellbeispiel: 632.030.TIALN Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 35° Point angle: 130° Chamfer: 4 facet pointing Carbide grade: EZ21 Point: Standard 632.124* 632.125 632.126* 632.127* 632.128* 632.129* 632.130 632.131 632.132 632.133 632.134 632.135 632.136* 632.137* 632.138 632.139* 632.140 632.141* 632.142* 632.143* 632.144 632.145 632.146 632.147 632.148 632.149* 632.150 632.151* 632.152* 632.153 632.154* 632.155 632.156* 632.157* 632.158* 632.159* 632.160 632.161 632.162 632.163 632.164 632.165 632.166 632.167* 632.168* 632.169* 632.170 632.171* Geometry and carbide designed for microprocessing of titanium, stainless steel, and harder materials. With point for self-centering and reduction of process heat. Available with TiAlN coating for optimum results when working with special materials. Ordering example: 632.030.TIALN Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° Angle de pointe: 130° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: standard Géométrie et sorte de carbure conçus pour le micro-usinage du titane, des aciers spéciaux et autres matériaux plus durs. Autocentrant et réduction de la chaleur du processus grâce à l'affûtage en pointe. Revêtement TiAlN pour résultats optimaux dans matières spéciales. d1 l1 l d 1,24 1,25 1,26 1,27 1,28 1,29 1,30 1,31 1,32 1,33 1,34 1,35 1,36 1,37 1,38 1,39 1,40 1,41 1,42 1,43 1,44 1,45 1,46 1,47 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,55 1,56 1,57 1,58 1,59 1,60 1,61 1,62 1,63 1,64 1,65 1,66 1,67 1,68 1,69 1,70 1,71 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 11,5 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Exemple de commande: 632.032.TIALN Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 61 632 VHM-Spiralbohrer mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° Spitzenwinkel: 130° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Standard Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Titan, Edelstahl und härtere Materialien. Durch Ausspitzung selbstzentrierend und Reduzierung der Prozesswärme. Mit TiAlN-Beschichtung erhältlich für optimale Ergebnisse bei Sonderwerkstoffen. Bestellbeispiel: 632.030.TIALN Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 35° Point angle: 130° Chamfer: 4 facet pointing Carbide grade: EZ21 Point: Standard 632.172* 632.173* 632.174* 632.175 632.176* 632.177* 632.178* 632.179* 632.180 632.181 632.182* 632.183* 632.184* 632.185 632.186* 632.187* 632.188* 632.189* 632.190 632.191* 632.192 632.193* 632.194* 632.195 632.196* 632.197* 632.198* 632.199* 632.200 632.205* 632.210 632.215* 632.220 632.225* 632.230 632.235* 632.240 632.245* 632.250 632.255* 632.260 632.265* 632.270 632.275* 632.280 632.285* 632.290 632.295* 632.300 Geometry and carbide designed for microprocessing of titanium, stainless steel, and harder materials. With point for self-centering and reduction of process heat. Available with TiAlN coating for optimum results when working with special materials. Ordering example: 632.030.TIALN Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° Angle de pointe: 130° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: standard Géométrie et sorte de carbure conçus pour le micro-usinage du titane, des aciers spéciaux et autres matériaux plus durs. Autocentrant et réduction de la chaleur du processus grâce à l'affûtage en pointe. Revêtement TiAlN pour résultats optimaux dans matières spéciales. d1 l1 l d 1,72 1,73 1,74 1,75 1,76 1,77 1,78 1,79 1,80 1,81 1,82 1,83 1,84 1,85 1,86 1,87 1,88 1,89 1,90 1,91 1,92 1,93 1,94 1,95 1,96 1,97 1,98 1,99 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 3,00 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 15,0 15,0 15,0 15,0 15,0 15,0 15,0 15,0 15,0 15,0 15,0 18,0 18,0 18,0 18,0 18,0 18,0 18,0 18,0 18,0 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Exemple de commande: 632.032.TIALN Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. 62 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 633 VHM-Spiralbohrer mit verstärktem Schaft 4xd 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30°, verstärkte Geometrie Spitzenwinkel: 140° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Spezial Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von hochfesten Materialien. Durch Ausspitzung selbstzentrierend und Reduzierung der Prozesswärme. Mit TiAlN-Beschichtung erhältlich für optimale Ergebnisse bei Sonderwerkstoffen. Bestellbeispiel: 633.078.TIALN Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 30°, reinforced geometry Point angle: 140° Chamfer: 4 facet pointing Carbide grade: EZ21 Pointed: Special 633.078 633.079 633.080 633.081 633.082 633.083 633.084* 633.085 633.086* 633.087* 633.088* 633.089* 633.090 633.091* 633.092* 633.093* 633.094* 633.095 633.096 633.097 633.098 633.099 633.100 633.101 633.102* 633.103 633.104* 633.105 633.106 633.107 633.108* 633.109 633.110 633.111* 633.112 633.113 633.114 633.115 633.116 633.117* 633.118* 633.119* 633.120 633.121* 633.122 633.123* 633.124* Geometry and carbide specially designed for the micromachining of high-strength materials. Point for self-centering and reduction of process heat. Available with TiAlN coating for optimum results when working with special materials. Ordering example: 633.078.TIALN Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30°, géométrie renforcée Angle de pointe: 140° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: spécial Géométrie et sorte de carbure spécialement conçus pour le micro-usinage de matériaux très durs. Autocentrant et réduction de la chaleur du processus grâce à l'affûtage en pointe. d1 l1 l d 0,78 0,79 0,80 0,81 0,82 0,83 0,84 0,85 0,86 0,87 0,88 0,89 0,90 0,91 0,92 0,93 0,94 0,95 0,96 0,97 0,98 0,99 1,00 1,01 1,02 1,03 1,04 1,05 1,06 1,07 1,08 1,09 1,10 1,11 1,12 1,13 1,14 1,15 1,16 1,17 1,18 1,19 1,20 1,21 1,22 1,23 1,24 3,3 3,4 3,4 3,4 3,5 3,5 3,6 3,6 3,7 3,7 3,7 3,8 3,8 3,9 3,9 4,0 4,0 4,0 4,1 4,1 4,2 4,2 4,3 4,3 4,3 4,4 4,4 4,5 4,5 4,5 4,6 4,6 4,7 4,7 4,8 4,8 4,8 4,9 4,9 5,0 5,0 5,1 5,1 5,1 5,2 5,2 5,3 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Revêtement TiAlN pour résultats optimaux dans matières spéciales. Exemple de commande: 633.078.TIALN Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 63 633 VHM-Spiralbohrer mit verstärktem Schaft 4xd 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30°, verstärkte Geometrie Spitzenwinkel: 140° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Spezial Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von hochfesten Materialien. Durch Ausspitzung selbstzentrierend und Reduzierung der Prozesswärme. Mit TiAlN-Beschichtung erhältlich für optimale Ergebnisse bei Sonderwerkstoffen. Bestellbeispiel: 633.078.TIALN Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 30°, reinforced geometry Point angle: 140° Chamfer: 4 facet pointing Carbide grade: EZ21 Pointed: Special 633.125 633.126* 633.127* 633.128* 633.129* 633.130 633.131 633.132 633.133 633.134 633.135 633.136* 633.137* 633.138 633.139* 633.140 633.141 633.142* 633.143* 633.144 633.145 633.146 633.147 633.148 633.149* 633.150 633.151* 633.152* 633.153 633.154* 633.155 633.156* 633.157* 633.158* 633.159* 633.160 633.161 633.162 633.163 633.164 633.165 633.166 633.167* 633.168* 633.169* 633.170 633.171* 633.172* Geometry and carbide specially designed for the micromachining of high-strength materials. Point for self-centering and reduction of process heat. Available with TiAlN coating for optimum results when working with special materials. Ordering example: 633.078.TIALN Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30°, géométrie renforcée Angle de pointe: 140° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: spécial Géométrie et sorte de carbure spécialement conçus pour le micro-usinage de matériaux très durs. Autocentrant et réduction de la chaleur du processus grâce à l'affûtage en pointe. Revêtement TiAlN pour résultats optimaux dans matières spéciales. d1 l1 l d 1,25 1,26 1,27 1,28 1,29 1,30 1,31 1,32 1,33 1,34 1,35 1,36 1,37 1,38 1,39 1,40 1,41 1,42 1,43 1,44 1,45 1,46 1,47 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,55 1,56 1,57 1,58 1,59 1,60 1,61 1,62 1,63 1,64 1,65 1,66 1,67 1,68 1,69 1,70 1,71 1,72 5,3 5,4 5,4 5,4 5,5 5,5 5,6 5,6 5,7 5,7 5,7 5,8 5,8 5,9 5,9 6,0 6,0 6,0 6,1 6,1 6,2 6,2 6,2 6,3 6,3 6,4 6,4 6,5 6,5 6,5 6,6 6,6 6,7 6,7 6,8 6,8 6,8 6,9 6,9 7,0 7,0 7,1 7,1 7,1 7,2 7,2 7,3 7,3 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Exemple de commande: 633.078.TIALN Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. 64 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 633 VHM-Spiralbohrer mit verstärktem Schaft 4xd 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30°, verstärkte Geometrie Spitzenwinkel: 140° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Spezial Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von hochfesten Materialien. Durch Ausspitzung selbstzentrierend und Reduzierung der Prozesswärme. Mit TiAlN-Beschichtung erhältlich für optimale Ergebnisse bei Sonderwerkstoffen. Bestellbeispiel: 633.078.TIALN Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 30°, reinforced geometry Point angle: 140° Chamfer: 4 facet pointing Carbide grade: EZ21 Pointed: Special 633.173* 633.174* 633.175 633.176* 633.177* 633.178* 633.179* 633.180 633.181* 633.182* 633.183* 633.184* 633.185 633.186* 633.187* 633.188* 633.189* 633.190 633.191* 633.192 633.193* 633.194* 633.195 633.196* 633.197* 633.198* 633.199* 633.200 633.205* 633.210 633.215* 633.220 633.225* 633.230 633.235* 633.240 633.245* 633.250 633.255* 633.260 633.265* 633.270 633.275* 633.280 633.285* 633.290 633.295* 633.300 Geometry and carbide specially designed for the micromachining of high-strength materials. Point for self-centering and reduction of process heat. Available with TiAlN coating for optimum results when working with special materials. Ordering example: 633.078.TIALN Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30°, géométrie renforcée Angle de pointe: 140° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: spécial Géométrie et sorte de carbure spécialement conçus pour le micro-usinage de matériaux très durs. Autocentrant et réduction de la chaleur du processus grâce à l'affûtage en pointe. Revêtement TiAlN pour résultats optimaux dans matières spéciales. Exemple de commande: 633.078.TIALN d1 l1 l d 1,73 1,74 1,75 1,76 1,77 1,78 1,79 1,80 1,81 1,82 1,83 1,84 1,85 1,86 1,87 1,88 1,89 1,90 1,91 1,92 1,93 1,94 1,95 1,96 1,97 1,98 1,99 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 3,00 7,4 7,4 7,4 7,5 7,5 7,6 7,6 7,7 7,7 7,7 7,8 7,8 7,9 7,9 7,9 8,0 8,0 8,1 8,1 8,2 8,2 8,2 8,3 8,3 8,4 8,4 8,5 8,5 8,7 8,9 9,1 9,4 9,6 9,8 10,0 10,2 10,4 10,6 10,8 11,1 11,3 11,5 11,7 11,9 12,1 12,3 12,5 12,8 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 65 634 VHM-Spiralbohrer mit verstärktem Schaft 7xd 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30°, verstärkte Geometrie Spitzenwinkel: 140° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Spezial Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von hochfesten Materialien. Durch Ausspitzung selbstzentrierend und Reduzierung der Prozesswärme. Mit TiAlN-Beschichtung erhältlich für optimale Ergebnisse bei Sonderwerkstoffen. Bestellbeispiel: 634.078.TIALN Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 30°, reinforced geometry Point angle: 140° Chamfer: 4 facet pointing Carbide grade: EZ21 Pointed: Special 634.078* 634.079* 634.080 634.081* 634.082* 634.083* 634.084* 634.085* 634.086* 634.087* 634.088* 634.089* 634.090 634.091* 634.092* 634.093* 634.094* 634.095* 634.096* 634.097* 634.098* 634.099* 634.100 634.101* 634.102* 634.103* 634.104* 634.105* 634.106* 634.107* 634.108* 634.109* 634.110 634.111* 634.112* 634.113* 634.114* 634.115* 634.116* 634.117* 634.118* 634.119* 634.120 634.121* 634.122* 634.123* 634.124* 634.125* Geometry and carbide specially designed for the micromachining of high-strength materials. Point for self-centering and reduction of process heat. Available with TiAlN coating for optimum results when working with special materials. Ordering example: 634.078.TIALN Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30°, géométrie renforcée Angle de pointe: 140° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: spécial Géométrie et sorte de carbure spécialement conçus pour le micro-usinage de matériaux très durs. Autocentrant et réduction de la chaleur du processus grâce à l'affûtage en pointe. Revêtement TiAlN pour résultats optimaux dans matières spéciales. d1 l1 l d 0,78 0,79 0,80 0,81 0,82 0,83 0,84 0,85 0,86 0,87 0,88 0,89 0,90 0,91 0,92 0,93 0,94 0,95 0,96 0,97 0,98 0,99 1,00 1,01 1,02 1,03 1,04 1,05 1,06 1,07 1,08 1,09 1,10 1,11 1,12 1,13 1,14 1,15 1,16 1,17 1,18 1,19 1,20 1,21 1,22 1,23 1,24 1,25 5,7 5,7 5,8 5,9 5,9 6,0 6,1 6,2 6,2 6,3 6,4 6,5 6,5 6,6 6,7 6,7 6,8 6,9 7,0 7,0 7,1 7,2 7,3 7,3 7,4 7,5 7,5 7,6 7,7 7,8 7,8 7,9 8,0 8,0 8,1 8,2 8,3 8,3 8,4 8,5 8,6 8,6 8,7 8,8 8,8 8,9 9,0 9,1 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Exemple de commande: 634.078.TIALN Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. 66 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 634 VHM-Spiralbohrer mit verstärktem Schaft 7xd 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30°, verstärkte Geometrie Spitzenwinkel: 140° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Spezial Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von hochfesten Materialien. Durch Ausspitzung selbstzentrierend und Reduzierung der Prozesswärme. Mit TiAlN-Beschichtung erhältlich für optimale Ergebnisse bei Sonderwerkstoffen. Bestellbeispiel: 634.078.TIALN Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 30°, reinforced geometry Point angle: 140° Chamfer: 4 facet pointing Carbide grade: EZ21 Pointed: Special 634.126* 634.127* 634.128* 634.129* 634.130 634.131* 634.132* 634.133* 634.134* 634.135* 634.136* 634.137* 634.138* 634.139* 634.140 634.141* 634.142* 634.143* 634.144* 634.145* 634.146* 634.147* 634.148* 634.149* 634.150 634.151* 634.152* 634.153* 634.154* 634.155* 634.156* 634.157* 634.158* 634.159* 634.160 634.161* 634.162* 634.163* 634.164* 634.165* 634.166* 634.167* 634.168* 634.169* 634.170 634.171* 634.172* 634.173* Geometry and carbide specially designed for the micromachining of high-strength materials. Point for self-centering and reduction of process heat. Available with TiAlN coating for optimum results when working with special materials. Ordering example: 634.078.TIALN Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30°, géométrie renforcée Angle de pointe: 140° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: spécial Géométrie et sorte de carbure spécialement conçus pour le micro-usinage de matériaux très durs. Autocentrant et réduction de la chaleur du processus grâce à l'affûtage en pointe. Revêtement TiAlN pour résultats optimaux dans matières spéciales. d1 l1 l d 1,26 1,27 1,28 1,29 1,30 1,31 1,32 1,33 1,34 1,35 1,36 1,37 1,38 1,39 1,40 1,41 1,42 1,43 1,44 1,45 1,46 1,47 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,55 1,56 1,57 1,58 1,59 1,60 1,61 1,62 1,63 1,64 1,65 1,66 1,67 1,68 1,69 1,70 1,71 1,72 1,73 9,1 9,2 9,3 9,4 9,4 9,5 9,6 9,6 9,7 9,8 9,9 9,9 10,0 10,1 10,2 10,2 10,3 10,4 10,4 10,5 10,6 10,7 10,7 10,8 10,9 10,9 11,0 11,1 11,2 11,2 11,3 11,4 11,5 11,5 11,6 11,7 11,7 11,8 11,9 12,0 12,0 12,1 12,2 12,3 12,3 12,4 12,5 12,5 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Exemple de commande: 634.078.TIALN Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 67 634 VHM-Spiralbohrer mit verstärktem Schaft 7xd 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 30°, verstärkte Geometrie Spitzenwinkel: 140° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Spezial Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von hochfesten Materialien. Durch Ausspitzung selbstzentrierend und Reduzierung der Prozesswärme. Mit TiAlN-Beschichtung erhältlich für optimale Ergebnisse bei Sonderwerkstoffen. Bestellbeispiel: 634.078.TIALN Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 30°, reinforced geometry Point angle: 140° Chamfer: 4 facet pointing Carbide grade: EZ21 Pointed: Special 634.174* 634.175* 634.176* 634.177* 634.178* 634.179* 634.180 634.181* 634.182* 634.183* 634.184* 634.185* 634.186* 634.187* 634.188* 634.189* 634.190 634.191* 634.192* 634.193* 634.194* 634.195* 634.196* 634.197* 634.198* 634.199* 634.200 634.205* 634.210 634.215* 634.220 634.225* 634.230 634.235* 634.240 634.245* 634.250 634.255* 634.260 634.265* 634.270 634.275* 634.280 634.285* 634.290 634.295* 634.300 Geometry and carbide specially designed for the micromachining of high-strength materials. Point for self-centering and reduction of process heat. Available with TiAlN coating for optimum results when working with special materials. Ordering example: 634.078.TIALN Foret hélicoïdal en carbure avec manche renforcé Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 30°, géométrie renforcée Angle de pointe: 140° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: spécial Géométrie et sorte de carbure spécialement conçus pour le micro-usinage de matériaux très durs. Autocentrant et réduction de la chaleur du processus grâce à l'affûtage en pointe. d1 l1 l d 1,74 1,75 1,76 1,77 1,78 1,79 1,80 1,81 1,82 1,83 1,84 1,85 1,86 1,87 1,88 1,89 1,90 1,91 1,92 1,93 1,94 1,95 1,96 1,97 1,98 1,99 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 3,00 12,6 12,7 12,8 12,8 12,9 13,0 13,1 13,1 13,2 13,3 13,3 13,4 13,5 13,6 13,6 13,7 13,8 13,8 13,9 14,0 14,1 14,1 14,2 14,3 14,4 14,4 14,5 14,9 15,2 15,6 16,0 16,3 16,7 17,0 17,4 17,8 18,1 18,5 18,9 19,2 19,6 19,9 20,3 20,7 21,0 21,4 21,8 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 Revêtement TiAlN pour résultats optimaux dans matières spéciales. Exemple de commande: 634.078.TIALN 68 Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 639 VHM-Spiralbohrer mit verstärktem Schaft Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° Spitzenwinkel: 120° Anschnitt: 4 Flächen HM-Sorte: EZ21 Ausspitzung: Standard Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Edelstahl wie 316L und zäheren Edelstählen. Solid carbide twist drills with reinforced shank Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: 35° Point angle: 120° Chamfer: 4 facet pointing Carbide grade: EZ21 Pointed: Standard 639.050 639.055* 639.060 639.065* 639.070 639.075* 639.080 639.085* 639.090 639.095* 639.100 639.105* 639.110 639.115* 639.120 639.125* 639.130 639.135* 639.140 639.145* 639.150 639.155* 639.160 639.165* 639.170 639.175* 639.180 639.185* 639.190 Geometry and carbide designed for microprocessing of stainless steel such as 316L and more ductile stainless steels. Foret hélicoïdal en carbure avec manche renforcé d 1 l1 l 0,50 0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1,00 1,05 1,10 1,15 1,20 1,25 1,30 1,35 1,40 1,45 1,50 1,55 1,60 1,65 1,70 1,75 1,80 1,85 1,90 4,0 4,5 4,5 5,0 5,6 5,6 6,3 6,3 7,1 7,1 9,0 9,0 9,0 9,0 10,0 10,0 10,0 11,2 11,2 11,2 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 12,0 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 38 38 38 38 38 38 38 38 38 d 1,0 1,0 1,0 1,0 1,0 1,0 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° Angle de pointe: 120° Affûtage: 4 facettes Sorte de carbure: EZ21 Affûtage en pointe: Standard Géométrie et sorte de carbure conçus pour le micro-usinage d’inox comme 316L et d'inox plus tenaces. Schnittdatenempfehlungen auf Seite 91. Cutting data recommendations on page 91. Recommandations de valeurs de coupe sur page 91. ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein * Kurzfristig lieferbar. * Available at short notice. * Livrable à bref délai. Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 69 635 8xd VHM-Mikro-Spiralbohrer 8xD mit Innenkühlung 1 Ø 1,50-2,05 mit / with / avec TURBO Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: ~30° Spitzenwinkel: 140° HM-Sorte: EZ44 Ausspitzung: Spezial Beschichung: TiAlN KAMMER / CHAMBER / CHAMBRE Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von hochfesten Materialien. Für hervorragende Ergebnisse bei tiefen Bohrungen im Mikrobereich. Optimale Kühlschmierung durch Turbo-Kammer im Schaft und große Bohrungen. Dadurch deutlich höhere Standzeit und bessere Oberflächengüte gegenüber konventioneller Bearbeitung. Solid carbide micro drills 8xD with inner coolant supply Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: ~30° Point angle: 140° Carbide grade: EZ44 Point: Special Coating: TiAlN 635.150.08 635.155.08 635.160.08 635.165.08 635.170.08 635.175.08 635.180.08 635.185.08 635.190.08 635.195.08 635.200.08 635.205.08 635.210.08 635.215.08 635.220.08 635.225.08 635.230.08 635.235.08 635.240.08 635.245.08 635.250.08 635.255.08 635.260.08 635.265.08 635.270.08 635.275.08 635.280.08 635.285.08 635.290.08 635.295.08 635.300.08 635.310.08 635.320.08 635.330.08 635.340.08 635.350.08 635.360.08 635.370.08 635.380.08 635.390.08 635.400.08 Geometry and carbide specially designed for micro-machining of high-strength materials. For best results at drilling of deep holes in the micro range. Optimum cooling lubrication due to the Turbo-Chamber in the shank and relative large cooling channels. Therefore significantly better tool time and surface quality compared to conventional machining. Micro-foret hélicoïdal en carbure monobloc 8xD à refroidissement intérieur Modèle: 2 dents Sens de coupe: droite Angle d'hélice: ~30° Angle de pointe: 140° Sorte de carbure: EZ44 Affûtage en pointe: Special Revêtement : TiAlN Géométrie et sorte de carbure spécialement conçus pour le micro-usinage de matériaux à résistance élevée. Pour des résultats exceptionnels de vos perçages profonds dans la gamme micro. Lubrification/ refroidissement optimisé par « chambre turbo » dans l‘embouchure et perçages de grandes dimensions. Les durées d‘usage sont de ce fait nettement prolongées ; par ailleurs, la qualité de surface est améliorée par rapport à un usinage à sec. 70 m m m m m m m m m m m m d1 l1 1,50 1,55 1,60 1,65 1,70 1,75 1,80 1,85 1,90 1,95 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 3,00 3,10 3,20 3,30 3,40 3,50 3,60 3,70 3,80 3,90 4,00 15,0 15,5 16,0 16,5 17,0 17,5 18,0 18,5 19,0 19,5 20,0 20,5 21,0 21,5 22,0 22,5 23,0 23,5 24,0 24,5 25,0 25,5 26,0 26,5 27,0 27,5 28,0 28,5 29,0 29,5 30,0 31,0 32,0 33,0 34,0 35,0 36,0 37,0 38,0 39,0 40,0 l 60 60 60 60 60 60 62 62 62 62 62 62 64 64 64 64 64 64 66 66 66 66 66 66 70 70 70 70 70 70 70 70 70 70 76 76 76 76 76 76 76 d 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 m Mit Turbo-Kammer. m With Turbo-Chamber. m Avec chambre turbo. Zwischenabmessungen ab Ø 0.75 mm, Sonderlängen bis 24xd1 und innengekühlte Stufenspiralbohrer auf Anfrage. Intermediate sizes of Ø 0.75 mm or more, special lengths up to 24xd1 and inner coolant step drills available on request. Dimensions intérmédiaires à partir du Ø 0.75 mm, longeurs spéciales jusqu‘à 24 x d1 et forets hélicoidaux étagés avec lubrification intérieure sur demande ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 635 16xd VHM-Mikro-Spiralbohrer 16xD mit Innenkühlung 1 Ø 1,50-2,05 mit / with / avec TURBO Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: ~30° Spitzenwinkel: 140° HM-Sorte: EZ44 Ausspitzung: Spezial Beschichung: TiAlN KAMMER / CHAMBER / CHAMBRE Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von hochfesten Materialien. Für hervorragende Ergebnisse bei tiefen Bohrungen im Mikrobereich. Optimale Kühlschmierung durch Turbo-Kammer im Schaft und große Bohrungen. Dadurch deutlich höhere Standzeit und bessere Oberflächengüte gegenüber konventioneller Bearbeitung. Solid carbide micro drills 16xD with inner coolant supply Bestell-Nr. order no N° référence Design: 2 flutes Cutting: RH Helix angle: ~30° Point angle: 140° Carbide grade: EZ44 Point: Special Coating: TiAlN 635.150.16 635.155.16 635.160.16 635.165.16 635.170.16 635.175.16 635.180.16 635.185.16 635.190.16 635.195.16 635.200.16 635.205.16 635.210.16 635.215.16 635.220.16 635.225.16 635.230.16 635.235.16 635.240.16 635.245.16 635.250.16 635.255.16 635.260.16 635.265.16 635.270.16 635.275.16 635.280.16 635.285.16 635.290.16 635.295.16 635.300.16 635.310.16 635.320.16 635.330.16 635.340.16 635.350.16 635.360.16 635.370.16 635.380.16 635.390.16 635.400.16 Geometry and carbide specially designed for micro-machining of high-strength materials. For best results at drilling of deep holes in the micro range. Optimum cooling lubrication due to the Turbo-Chamber in the shank and relative large cooling channels. Therefore significantly better tool time and surface quality compared to conventional machining. Micro-foret hélicoïdal en carbure monobloc 16xD à refroidissement intérieur Modèle: 2 dents Sens de coupe: droite Angle d'hélice: ~30° Angle de pointe: 140° Sorte de carbure: EZ44 Affûtage en pointe: Special Revêtement : TiAlN Géométrie et sorte de carbure spécialement conçus pour le micro-usinage de matériaux à résistance élevée. Pour des résultats exceptionnels de vos perçages profonds dans la gamme micro. Lubrification/ refroidissement optimisé par « chambre turbo » dans l‘embouchure et perçages de grandes dimensions. Les durées d‘usage sont de ce fait nettement prolongées ; par ailleurs, la qualité de surface est améliorée par rapport à un usinage à sec. m m m m m m m m m m m m d1 l1 1,50 1,55 1,60 1,65 1,70 1,75 1,80 1,85 1,90 1,95 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 3,00 3,10 3,20 3,30 3,40 3,50 3,60 3,70 3,80 3,90 4,00 27,0 27,9 28,8 29,7 30,6 31,5 32,4 33,3 34,2 35,1 36,0 36,9 37,8 38,7 39,6 40,5 41,4 42,3 43,2 44,1 45,0 45,9 46,8 47,7 48,6 49,5 50,4 51,3 52,2 53,1 54,0 55,8 57,6 59,4 61,2 63,0 64,8 66,6 68,4 70,2 72,0 l 72 72 72 72 72 72 77 77 77 77 77 81 81 81 81 81 81 85 85 85 85 85 85 91 91 91 91 91 91 91 91 91 91 91 104 104 104 104 104 104 104 d 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 m Mit Turbo-Kammer. m With Turbo-Chamber. m Avec chambre turbo. Zwischenabmessungen ab Ø 0.75 mm, Sonderlängen bis 24xd1 und innengekühlte Stufenspiralbohrer auf Anfrage. Intermediate sizes of Ø 0.75 mm or more, special lengths up to 24xd1 and inner coolant step drills available on request. Dimensions intérmédiaires à partir du Ø 0.75 mm, longeurs spéciales jusqu‘à 24 x d1 et forets hélicoidaux étagés avec lubrification intérieure sur demande ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 71 636 8xd WINNER VHM-Mikro-Spiralbohrer mit degressiver Spirale, 8xD Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° > 12° degressiv Spitzenwinkel: 120° HM-Sorte: EZ21 Ausspitzung: Spezial Beschichung: TiAlN Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Titan, Edelstahl, zähen Materialien und bei erschwerter Spanabfuhr. Sehr gute Alternative für tiefe Bohrungen ohne Innenkühlung. Effizienter Spantransport auch bei schwierigen Materialien durch sich öffnende degressive Geometrie. Durch hohe Vorschübe und stabile Schneidengeometrie optimal geeignet für lange Standzeiten in der Großserienfertigung. WINNER Solid carbide micro drills with degressive flutes, 8xD Design: 2 flutes Cutting: RH Helix angle: 35° > 12° degressive Point angle: 120° Carbide grade: EZ21 Point: Special Coating: TiAlN Geometry and carbide designed for micromachining of titanium, stainless steel, tough materials and difficult chip removal applications. Very good alternative for deep holes without internal coolant supply. Outstanding chip removal on machining of difficult materials by a degressive ‘QuickChip” flute design. Due to high feed rates and stable cutting edge geometry suitable for long service life in large-scale volume production. WINNER Micro-foret hélicoïdal en carbure monobloc à hélice dégressive, 8xD Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° > 12° dégressive Angle de pointe: 120° Affûtage: Spécial Sorte de carbure: EZ21 Affûtage en pointe: Spécial Revêtement: TiAlN Géométrie et sorte de carbure conçus pour le micro-usinage du titane, des aciers spéciaux et autres matériaux plus durs. L‘alternative parfaite pour les perçages profonds sans refroidissement intérieur. Evacuation performante des copeaux même sur les matériaux difficiles, grâce à la géométrie dégressive. Les avances élevées et la stabilité de la géométrie des coupes permettent des durées d‘usage élevées dans la fabrication de grandes séries. 72 Bestell-Nr. order no N° référence 636.050.08 636.055.08 636.060.08 636.065.08 636.070.08 636.075.08 636.080.08 636.085.08 636.090.08 636.095.08 636.100.08 636.105.08 636.110.08 636.115.08 636.120.08 636.125.08 636.130.08 636.135.08 636.140.08 636.145.08 636.150.08 636.155.08 636.160.08 636.165.08 636.170.08 636.175.08 636.180.08 636.185.08 636.190.08 636.195.08 636.200.08 636.205.08 636.210.08 636.215.08 636.220.08 636.225.08 636.230.08 636.235.08 636.240.08 636.245.08 636.250.08 636.255.08 636.260.08 636.265.08 636.270.08 636.275.08 636.280.08 636.285.08 636.290.08 636.295.08 636.300.08 d1 l1 d l 0,50 0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1,00 1,05 1,10 1,15 1,20 1,25 1,30 1,35 1,40 1,45 1,50 1,55 1,60 1,65 1,70 1,75 1,80 1,85 1,90 1,95 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 3,00 3,8 4,1 4,5 4,9 5,3 5,6 6,0 6,4 6,8 7,1 7,5 7,9 8,3 8,6 9,0 9,4 9,8 10,1 10,5 10,9 11,3 11,6 12,0 12,4 12,8 13,1 13,5 13,9 14,3 14,6 15,0 15,4 15,8 16,1 16,5 16,9 17,3 17,6 18,0 18,4 18,8 19,1 19,5 19,9 20,3 20,6 21,0 21,4 21,8 22,1 22,5 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 45 53 53 53 53 53 53 53 53 53 53 53 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 1 636 12xd WINNER VHM-Mikro-Spiralbohrer mit degressiver Spirale, 12xD 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° > 12° degressiv Spitzenwinkel: 120° HM-Sorte: EZ21 Ausspitzung: Spezial Beschichung: TiAlN Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Titan, Edelstahl, zähen Materialien und bei erschwerter Spanabfuhr. Sehr gute Alternative für tiefe Bohrungen ohne Innenkühlung. Effizienter Spantransport auch bei schwierigen Materialien durch sich öffnende degressive Geometrie. Durch hohe Vorschübe und stabile Schneidengeometrie optimal geeignet für lange Standzeiten in der Großserienfertigung. WINNER Solid carbide micro drills with degressive flutes, 12xD Design: 2 flutes Cutting: RH Helix angle: 35° > 12° degressive Point angle: 120° Carbide grade: EZ21 Point: Special Coating: TiAlN Geometry and carbide designed for micromachining of titanium, stainless steel, tough materials and difficult chip removal applications. Very good alternative for deep holes without internal coolant supply. Outstanding chip removal on machining of difficult materials by a degressive ‘QuickChip” flute design. Due to high feed rates and stable cutting edge geometry suitable for long service life in large-scale volume production. WINNER Micro-foret hélicoïdale en carbure monobloc à hélice dégressive, 12xD Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° > 12° dégressive Angle de pointe: 120° Affûtage: Spécial Sorte de carbure: EZ21 Affûtage en pointe: Spécial Revêtement: TiAlN Géométrie et sorte de carbure conçus pour le micro-usinage du titane, des aciers spéciaux et autres matériaux plus durs. L‘alternative parfaite pour les perçages profonds sans refroidissement intérieur. Evacuation performante des copeaux même sur les matériaux difficiles, grâce à la géométrie dégressive. Les avances élevées et la stabilité de la géométrie des coupes permettent des durées d‘usage élevées dans la fabrication de grandes séries. Bestell-Nr. order no N° référence 636.050.12 636.055.12 636.060.12 636.065.12 636.070.12 636.075.12 636.080.12 636.085.12 636.090.12 636.095.12 636.100.12 636.105.12 636.110.12 636.115.12 636.120.12 636.125.12 636.130.12 636.135.12 636.140.12 636.145.12 636.150.12 636.155.12 636.160.12 636.165.12 636.170.12 636.175.12 636.180.12 636.185.12 636.190.12 636.195.12 636.200.12 636.205.12 636.210.12 636.215.12 636.220.12 636.225.12 636.230.12 636.235.12 636.240.12 636.245.12 636.250.12 636.255.12 636.260.12 636.265.12 636.270.12 636.275.12 636.280.12 636.285.12 636.290.12 636.295.12 636.300.12 d1 l1 d l 0,50 0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1,00 1,05 1,10 1,15 1,20 1,25 1,30 1,35 1,40 1,45 1,50 1,55 1,60 1,65 1,70 1,75 1,80 1,85 1,90 1,95 2,00 2,05 2,10 2,15 2,20 2,25 2,30 2,35 2,40 2,45 2,50 2,55 2,60 2,65 2,70 2,75 2,80 2,85 2,90 2,95 3,00 6,8 7,4 8,1 8,8 9,5 10,1 10,8 11,5 12,2 12,8 13,5 14,2 14,9 15,5 16,2 16,9 17,6 18,2 18,9 19,6 20,3 20,9 21,6 22,3 23,0 23,6 24,3 25,0 25,7 26,3 27,0 27,7 28,4 29,0 29,7 30,4 31,1 31,7 32,4 33,1 33,8 34,4 35,1 35,8 36,5 37,1 37,8 38,5 39,2 39,8 40,5 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 38 38 38 38 38 38 38 38 38 38 45 45 45 45 45 45 45 45 45 45 53 53 53 53 53 53 53 53 53 53 64 64 64 64 64 64 64 64 64 64 64 75 75 75 75 75 75 75 75 75 75 ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 73 637 8xd WINNER VHM-Mikro-Spiralbohrer mit degressiver Spirale, 8xD 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° > 12° degressiv Spitzenwinkel: 140° HM-Sorte: EZ21 Ausspitzung: Spezial Beschichung: TiAlN Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Titan, Edelstahl, zähen Materialien und bei erschwerter Spanabfuhr. Sehr gute Alternative für tiefe Bohrungen ohne Innenkühlung. Effizienter Spantransport auch bei schwierigen Materialien durch sich öffnende degressive Geometrie. Durch hohe Vorschübe und stabile Schneidengeometrie optimal geeignet für lange Standzeiten in der Großserienfertigung. WINNER Solid carbide micro drills with degressive flutes, 8xD Design: 2 flutes Cutting: RH Helix angle: 35° > 12° degressive Point angle: 140° Carbide grade: EZ21 Point: Special Coating: TiAlN Geometry and carbide designed for micromachining of titanium, stainless steel, tough materials and difficult chip removal applications. Very good alternative for deep holes without internal coolant supply. Outstanding chip removal on machining of difficult materials by a degressive ‘QuickChip” flute design. Due to high feed rates and stable cutting edge geometry suitable for long service life in large-scale volume production. WINNER Micro-foret hélicoïdal en carbure monobloc à hélice dégressive, 8xD Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° > 12° dégressive Angle de pointe: 140° Affûtage: Spécial Sorte de carbure: EZ21 Affûtage en pointe: Spécial Revêtement: TiAlN Géométrie et sorte de carbure conçus pour le micro-usinage du titane, des aciers spéciaux et autres matériaux plus durs. L‘alternative parfaite pour les perçages profonds sans refroidissement intérieur. Evacuation performante des copeaux même sur les matériaux difficiles, grâce à la géométrie dégressive. Les avances élevées et la stabilité de la géométrie des coupes permettent des durées d‘usage élevées dans la fabrication de grandes séries. 74 Bestell-Nr. order no N° référence 637.300.08 637.305.08 637.310.08 637.315.08 637.320.08 637.325.08 637.330.08 637.335.08 637.340.08 637.345.08 637.350.08 637.355.08 637.360.08 637.365.08 637.370.08 637.375.08 637.380.08 637.385.08 637.390.08 637.395.08 637.400.08 637.405.08 637.410.08 637.415.08 637.420.08 637.425.08 637.430.08 637.435.08 637.440.08 637.445.08 637.450.08 637.455.08 637.460.08 637.465.08 637.470.08 637.475.08 637.480.08 637.485.08 637.490.08 637.495.08 637.500.08 637.505.08 637.510.08 637.515.08 637.520.08 637.525.08 637.530.08 637.535.08 637.540.08 637.545.08 637.550.08 d1 l1 l d 3,00 3,05 3,10 3,15 3,20 3,25 3,30 3,35 3,40 3,45 3,50 3,55 3,60 3,65 3,70 3,75 3,80 3,85 3,90 3,95 4,00 4,05 4,10 4,15 4,20 4,25 4,30 4,35 4,40 4,45 4,50 4,55 4,60 4,65 4,70 4,75 4,80 4,85 4,90 4,95 5,00 5,05 5,10 5,15 5,20 5,25 5,30 5,35 5,40 5,45 5,50 24,0 24,4 24,8 25,2 25,6 26,0 26,4 26,8 27,2 27,6 28,0 28,4 28,8 29,2 29,6 30,0 30,4 30,8 31,2 31,6 32,0 32,4 32,8 33,2 33,6 34,0 34,4 34,8 35,2 35,6 36,0 36,4 36,8 37,2 37,6 38,0 38,4 38,8 39,2 39,6 40,0 40,4 40,8 41,2 41,6 42,0 42,4 42,8 43,2 43,6 44,0 75 75 75 75 75 75 75 75 75 75 75 75 75 80 80 80 80 80 80 80 80 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 107 107 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 NEU / NEW / NOUVEAU ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 637 8xd WINNER VHM-Mikro-Spiralbohrer mit degressiver Spirale, 8xD 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° > 12° degressiv Spitzenwinkel: 140° HM-Sorte: EZ21 Ausspitzung: Spezial Beschichung: TiAlN Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Titan, Edelstahl, zähen Materialien und bei erschwerter Spanabfuhr. Sehr gute Alternative für tiefe Bohrungen ohne Innenkühlung. Effizienter Spantransport auch bei schwierigen Materialien durch sich öffnende degressive Geometrie. Durch hohe Vorschübe und stabile Schneidengeometrie optimal geeignet für lange Standzeiten in der Großserienfertigung. WINNER Solid carbide micro drills with degressive flutes, 8xD Design: 2 flutes Cutting: RH Helix angle: 35° > 12° degressive Point angle: 140° Carbide grade: EZ21 Point: Special Coating: TiAlN Bestell-Nr. order no N° référence 637.560.08 637.565.08 637.570.08 637.575.08 637.580.08 637.585.08 637.590.08 637.595.08 637.600.08 d1 l1 5,60 5,65 5,70 5,75 5,80 5,85 5,90 5,95 6,00 44,8 45,2 45,6 46,0 46,4 46,8 47,2 47,6 48,0 l 107 107 107 107 107 107 107 107 107 d 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 Geometry and carbide designed for micromachining of titanium, stainless steel, tough materials and difficult chip removal applications. Very good alternative for deep holes without internal coolant supply. Outstanding chip removal on machining of difficult materials by a degressive ‘QuickChip” flute design. Due to high feed rates and stable cutting edge geometry suitable for long service life in large-scale volume production. WINNER Micro-foret hélicoïdale en carbure monobloc à hélice dégressive, 8xD Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° > 12° dégressive Angle de pointe: 140° Affûtage: Spécial Sorte de carbure: EZ21 Affûtage en pointe: Spécial Revêtement: TiAlN Géométrie et sorte de carbure conçus pour le micro-usinage du titane, des aciers spéciaux et autres matériaux plus durs. L‘alternative parfaite pour les perçages profonds sans refroidissement intérieur. Evacuation performante des copeaux même sur les matériaux difficiles, grâce à la géométrie dégressive. Les avances élevées et la stabilité de la géométrie des coupes permettent des durées d‘usage élevées dans la fabrication de grandes séries. NEU / NEW / NOUVEAU ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 75 637 12xd WINNER VHM-Mikro-Spiralbohrer mit degressiver Spirale, 12xD 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° > 12° degressiv Spitzenwinkel: 140° HM-Sorte: EZ21 Ausspitzung: Spezial Beschichung: TiAlN Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Titan, Edelstahl, zähen Materialien und bei erschwerter Spanabfuhr. Sehr gute Alternative für tiefe Bohrungen ohne Innenkühlung. Effizienter Spantransport auch bei schwierigen Materialien durch sich öffnende degressive Geometrie. Durch hohe Vorschübe und stabile Schneidengeometrie optimal geeignet für lange Standzeiten in der Großserienfertigung. WINNER Solid carbide micro drills with degressive flutes, 12xD Design: 2 flutes Cutting: RH Helix angle: 35° > 12° degressive Point angle: 140° Carbide grade: EZ21 Point: Special Coating: TiAlN Geometry and carbide designed for micromachining of titanium, stainless steel, tough materials and difficult chip removal applications. Very good alternative for deep holes without internal coolant supply. Outstanding chip removal on machining of difficult materials by a degressive ‘QuickChip” flute design. Due to high feed rates and stable cutting edge geometry suitable for long service life in large-scale volume production. WINNER Micro-foret hélicoïdal en carbure monobloc à hélice dégressive, 12xD Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° > 12° dégressive Angle de pointe: 140° Affûtage: Spécial Sorte de carbure: EZ21 Affûtage en pointe: Spécial Revêtement: TiAlN Géométrie et sorte de carbure conçus pour le micro-usinage du titane, des aciers spéciaux et autres matériaux plus durs. L‘alternative parfaite pour les perçages profonds sans refroidissement intérieur. Evacuation performante des copeaux même sur les matériaux difficiles, grâce à la géométrie dégressive. Les avances élevées et la stabilité de la géométrie des coupes permettent des durées d‘usage élevées dans la fabrication de grandes séries. 76 Bestell-Nr. order no N° référence 637.300.12 637.305.12 637.310.12 637.315.12 637.320.12 637.325.12 637.330.12 637.335.12 637.340.12 637.345.12 637.350.12 637.355.12 637.360.12 637.365.12 637.370.12 637.375.12 637.380.12 637.385.12 637.390.12 637.395.12 637.400.12 637.405.12 637.410.12 637.415.12 637.420.12 637.425.12 637.430.12 637.435.12 637.440.12 637.445.12 637.450.12 637.455.12 637.460.12 637.465.12 637.470.12 637.475.12 637.480.12 637.485.12 637.490.12 637.495.12 637.500.12 637.505.12 637.510.12 637.515.12 637.520.12 637.525.12 637.530.12 637.535.12 637.540.12 637.545.12 637.550.12 637.555.12 d1 l1 l d 3,00 3,05 3,10 3,15 3,20 3,25 3,30 3,35 3,40 3,45 3,50 3,55 3,60 3,65 3,70 3,75 3,80 3,85 3,90 3,95 4,00 4,05 4,10 4,15 4,20 4,25 4,30 4,35 4,40 4,45 4,50 4,55 4,60 4,65 4,70 4,75 4,80 4,85 4,90 4,95 5,00 5,05 5,10 5,15 5,20 5,25 5,30 5,35 5,40 5,45 5,50 5,55 36,0 36,6 37,2 37,8 38,4 39,0 39,6 40,2 40,8 41,4 42,0 42,6 43,2 43,8 44,4 45,0 45,6 46,2 46,8 47,4 48,0 48,6 49,2 49,8 50,4 51,0 51,6 52,2 52,8 53,4 54,0 54,6 55,2 55,8 56,4 57,0 57,6 58,2 58,8 59,4 60,0 60,6 61,2 61,8 62,4 63,0 63,6 64,2 64,8 65,4 66,0 66,6 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 107 107 107 107 107 107 107 107 107 107 107 107 107 107 107 107 107 107 107 107 122 122 122 122 122 122 122 122 122 122 122 4,0 4,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 NEU / NEW / NOUVEAU ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 637 12xd WINNER VHM-Mikro-Spiralbohrer mit degressiver Spirale, 12xD 1 Ausführung: 2 Schneiden Schnittrichtung: rechts Drallwinkel: 35° > 12° degressiv Spitzenwinkel: 140° HM-Sorte: EZ21 Ausspitzung: Spezial Beschichung: TiAlN Geometrie und Hartmetall speziell ausgelegt für die Mikrobearbeitung von Titan, Edelstahl, zähen Materialien und bei erschwerter Spanabfuhr. Sehr gute Alternative für tiefe Bohrungen ohne Innenkühlung. Effizienter Spantransport auch bei schwierigen Materialien durch sich öffnende degressive Geometrie. Durch hohe Vorschübe und stabile Schneidengeometrie optimal geeignet für lange Standzeiten in der Großserienfertigung. WINNER Solid carbide micro drills with degressive flutes, 12xD Design: 2 flutes Cutting: RH Helix angle: 35° > 12° degressive Point angle: 140° Carbide grade: EZ21 Point: Special Coating: TiAlN Bestell-Nr. order no N° référence 637.560.12 637.565.12 637.570.12 637.575.12 637.580.12 637.585.12 637.590.12 637.595.12 637.600.12 d1 l1 5,60 5,65 5,70 5,75 5,80 5,85 5,90 5,95 6,00 67,2 67,8 68,4 69,0 69,6 70,2 70,8 71,4 72,0 l 122 122 122 122 122 122 122 122 122 d 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 Geometry and carbide designed for micromachining of titanium, stainless steel, tough materials and difficult chip removal applications. Very good alternative for deep holes without internal coolant supply. Outstanding chip removal on machining of difficult materials by a degressive ‘QuickChip” flute design. Due to high feed rates and stable cutting edge geometry suitable for long service life in large-scale volume production. WINNER Micro-foret hélicoïdale en carbure monobloc à hélice dégressive, 12xD Modèle: 2 dents Sens de coupe: droite Angle d'hélice: 35° > 12° dégressive Angle de pointe: 140° Affûtage: Spécial Sorte de carbure: EZ21 Affûtage en pointe: Spécial Revêtement: TiAlN Géométrie et sorte de carbure conçus pour le micro-usinage du titane, des aciers spéciaux et autres matériaux plus durs. L‘alternative parfaite pour les perçages profonds sans refroidissement intérieur. Evacuation performante des copeaux même sur les matériaux difficiles, grâce à la géométrie dégressive. Les avances élevées et la stabilité de la géométrie des coupes permettent des durées d‘usage élevées dans la fabrication de grandes séries. NEU / NEW / NOUVEAU ZECHA Hartmetall-Werkzeugfabrikation GmbH Benzstraße 2 D-75203 Königsbach-Stein Tel. +49 (0) 72 32 / 30 22-0 Fax +49 (0) 72 32 / 30 22-25 [email protected] www.zecha.de 77